LankeCMS LOGO
Other parts
Hits:15162
Catphan500
Hits:12843
astro tool 615708
Hits:11879
Schlage
Hits:11581
PRODUCTS LIST Home > Product Show
Signal craft 44 GHz Frequency Converter SC2444

Product Numbers: 2023728143128

Product description: Brand:Signal craft model:SC2444 If you want to learn about the product, please contact us. Please provide the brand, model, and quantity for inquiry.

INTRODUCTION

Power is provided via a 12-volt wall cube which is included with the Development Kit. An embedded fan and temperature monitoring are integrated into the unit to manage heat.

Control of the module is provided via the USB, UART, or SPI interfaces. Most users will find it convenient to control the module using the console interface over USB. Alternatively, embedded controllers may access the UART or SPI interfaces available on the external Control Ports.

Two API protocols are available. The first is ASCII-based, and its commands follow the SCPI structure as defined in IEEE 488.2. The second is a binary protocol, targeted at embedded control applications where speed and timing are critical. Both protocols are detailed in an API Specification.

Up to 4 units can be combined in a vertical stack to create a complex 4 x 4 MIMO radio system. In this scenario, the internal control buses are routed to the cascaded modules over the Expansion Port. In this manner, API commands sent on the primary unit, can be redirected to the downstream modules. This eliminates the need for multiple controllers and simplifies timing and synchronization between units. Module addresses are set using a DIP switch on the Configuration Port.

Secondary and External Controls Port are also available. These ports expose Power, SPI, I2C, UART and GPIO that provide users with a convenient method of interfacing to external front-end modules, such as integrated antenna arrays or switched filter banks.

The low-frequency RF inputs include the IF, I/Q, external LO, and external frequency reference ports on SMA connectors.

The converters can be configured to interface with either IF or I/Q signals. The IF port supports signals between 2 and 6 GHz. The I/Q inputs provide connectivity to external single-ended DACs operating at up to 6 GHz. A low pass filter is included to help with alias and spurious rejection.

RadioThorium can be used in either Time Division Duplex (TDD) or Frequency Division Duplex (FDD) mode. The mmWave ports include 2.4 mm connectors for the FDD TX and RX functions, in addition to a bidirectional TDD port.

In FDD Mode, the Up-Conversion (UC) path has approximately 30 dB of gain and an output compression point, or P1dB, of 18 dBm at 40 GHz.  In TDD mode, the gain is also 30 dB, but the P1dB reduces to 16 dBm at 40 GHz.

In FDD Mode, the Down-Conversion (DC) path has a maximum gain of approximately 70 dB, noise figure of 10 dB, and an input compression point, or P1dB, of 0 dBm at 40 GHz.  In TDD mode, the gain is also close to 70 dB with a noise figure of 12 dB, and an input P1dB of better than 0 dBm at 40 GHz.

Two on-board Local Oscillators (LOs) are provided to facilitate standalone operation. Each LO can be configured independent of the other, providing users with complete control of the RF/LO/IF frequency plan specific to their application.

Optionally, the onboard synthesizers can be disabled when external LOs are supplied by the user.

Typical Applications

  • 5G NR Frequency Range 2 Development
  • Software Defined Radio Applications
  • Aerospace and Defense
  • Advanced Wireless Communications Research
Links: coastaltrading  |   JAPLAU  |   coast-hk  |   coastbuyer  |   coastaltrading  |  
  COASTAL TRADING INC. All rights reserved 粤ICP备11054825号-3
  Add:12042 SE Sunnyside Rd, Clackamas Oregon 97015, USA Tel: (503) 214-2838 Fax:Coastal Trading Inc.
  COASTAL TRADING INC. All rights reserved 粤ICP备11054825号-3